8X1 jilayaasha FSTN LCD bandhigay
Hordhac Product
| Nambarka Model | RXMC-0801C |
| Cabbirka Muujinta | 39.4X8 (VA) |
| Nooca | Dabeecad |
| Qaabka muuqaalka | FSTN, is beddel wanaagsan |
| MUUQAAL NOLOSHA | 8X1 jilayaal |
| KU SHAQEYNTA Voltage | 3.1 ~ 3.5V |
| Ka shaqee hadda | 0.5mA (3.3V) |
| Cabbirka jilaha | 3.7X5.95(WXH) mm |
| Interface | SERIAL, 3-SPI |
| Darawalka LCD IC | ST7070 AMA U dhigma |
| Eeg jihada | 12H |
| Iftiin danbe | buluug, casaan, cagaar |
| Heerkulka shaqada | -10 ~ +70 ℃ |
| Heerkulka kaydinta | -20 ~ + 80 ℃ |
| Codsiga | Character, bandhigay digit for printer, qalab iyo wixii la mid ah |
Tilmaamaha is-dhexgalka:
| PIN NO. | Astaanta | SHARAXAADA SHAQADA |
| 1 | VSS | Dhulka awoodda |
| 2 | VDD | awood anode |
| 3 | CS | CS gelinta |
| 4 | SCL | Saacad gelida keliga ah |
| 5 | SI | Gelida xogta |
| 6 | /RES | reset signal (heerka hoose sidoo kale waa saamayn) |
| 7 | A | anode iftiinka dambe |
| 8 | K | Kathode-ka dhabarka |
Adeegyadayada
KABADEED:
| Bandhig | qayb, garaaf, cutubka monochrome LCD module&TFT waa la aqbalay |
| Qaabka muuqaalka | TN, STN, FSTN,HTN, beddela, milicsi, gudbiye, cagaar jaale, buluug, cawl optional |
| Nooca muujinta | COB,COG, TAB |
| miisaanka Lcd (cm) | 0.11,0.14 |
| dhumucda iftiinka dambe (cm) | 2.8,3.0,3.3 |
| Interface | Barbarro (8bit, 4bit, 16 bit, 80 mode, 68mode), taxane (i2c, spi, uart, usb) |
| Xakamaynta | Ikhtiyaari |
| IC | Dhimasho ama baakad ikhtiyaari ah |
| Hardware ama software | Dhammaan waa la aqbalay |
| Xog la siiyay | Dhammaan fikradaha, muunad, sawir, sawir-qaadis, buug-gacmeedka iyo wixii la mid ah waa OK |
1, waxaan rabaaModule-ka LCD wuxuu soo bandhigay 8 nambar, cabbirkuna waa 35mm*70mm………?
Jawaab: Dhib malahan. Marka hore, pls noo soo dir warqaddaada sawir-qaadista ama muunadaha; waxaanu soo bandhigi doonaa midka ku haboon haddii ay tahay alaabooyinka caadiga ah. Ama waxaan wax ka beddeli karnaa iyada oo ku saleysan mid ka mid ah.
2,Module LCD-kan waa waxa aan rabno, laakiin waa cabbir weyn, ma haysaa wax ka yar?Aiyo waxa ku jira waxa ay u baahan yihiin in wax yar la beddelo.
Jawaab: Qaybta nooca LCD moduleka, haddii aad u baahan tahay wax ka beddel cabbirka dulucda ama waxa ku jira, muraayad LCD cusub ah ayaa loo baahan yahay. Waxaan ku ogeysiin doonaa lacagta caaryada kadib xaqiijinta marka lacag bixinta
Waxaan u bilaabi doonaa warqadda sawirka si aad u hubiso.
3, Tani module LCD nalka gadaal waa huruud-cagaaran,laakiin Iwaxay rabaan nalka dambe ee buluugga ah.
Jawaab: dhib malahan, waan kuu bedeli karnaa.
4, Waxaan doonayaa in aan astaysto module LCD cusub.Cma samaynaysaa?
Jawaab: Haa, waan awoodnaa. Fadlan soo dir warqaddaada sawir-qaadista. Haddii aadan haysan, fadlan ii sheeg cabbirka dulucda bandhigga LCD, macluumaadka muujinta, haddii loo baahdo nalka dambe ama guddiga PCB ee leh IC, Waxaan qiimeyn doonnaa qiimaha
oo aan ku siin qiimo dhaqso ah.
5, Waa maxay wakhtiga hogaaminaya qalabaynta
Jawaab: 15 ilaa 30 maalmood ka dib markaad sawirto caddaynta warqadda iyo bixinta kharashka qalabka, waxaanu kuu sheegi karnaa wakhtiga saxda ah ee aad xaqiijinayso warqad sawir leh.
6,Ma noo soo diri kartaa muunado hubin?
Jawaab: Haa,. Dalabka muunado ayaa diyaar ah
7,waa maxayWaqtiga hogaaminta?
Jawaab: Haddii aan haysanno kayd kuwa caadiga ah, wakhtiga hogaaminta waa hal maalin kadib lacag bixinta. Haddii ay tahay wax soo saarka tirada badan ee kuwa gaarka ah, wakhtiga hogaaminta waa qiyaastii 1530 maalmood. Haddii aan hore u dhammayn karno, waanu diri doonaa
akhbaartaada ka hor
8, Waa maxay hababka lacag bixinta ee aad aqbali kartaa?
Jawaab: Waxaan hadda aqbalnaa kaliya T/T.